The cost of replacing the head on a 3.6 Pentastar engine will vary depending on the make and model of the vehicle. Generally, the cost will be between $3,000 and $5,000. This includes the cost of parts and labor.
If your Chrysler vehicle is equipped with a 3.6L Pentastar engine, you may be wondering about the cost of replacing the head. Fortunately, this repair is not as expensive as it could be. The average cost of a 3.6 Pentastar head replacement is between $3,000 and $5,000.
This includes both parts and labor costs. While this may seem like a lot of money, it’s important to remember that this is a major repair. Replacing the head on your engine is a big job, and it’s not something that should be taken lightly.
If you’re considering having this repair done, be sure to get estimates from several reputable mechanics before making your final decision.
2018 Jeep Wrangler Rubicon JKUR -5 Minute Mods- 3.6 Pentastar Cylinder Head Replacement (Time Lapse)
How Much Does It Cost to Replace Engine Heads?
If your engine heads need to be replaced, it’ll cost you. Depending on the type of engine, materials, and labor involved, replacing engine heads can range from $1,000 to $4,000 or more.
For example, if you have a V8 engine made with aluminum heads, you’re looking at a replacement cost of around $2,500 to $3,500.
If your V8 engine has iron heads, the cost goes up to about $3,000 to $4,000. And if you have a six-cylinder engine with aluminum heads, expect to pay between $1,500 and $2,500 for the replacement job.
Of course, these are just estimates based on average prices charged by auto repair shops.
The actual cost of replacing your engine heads will depend on the make and model of your vehicle as well as the particular shop you take it to for service.
How Much Does It Cost to Get Cylinder Heads Done?
Cylinder heads are a vital component of any internal combustion engine, and as such, they need to be in good working order to ensure the engine runs smoothly. cylinder head repairs can be costly, depending on the severity of the damage and the make and model of the vehicle. Here is a breakdown of some common cylinder head repair costs:
Minor cracks or leaks: $200-$600
Major cracks or leaks: $1,000-$4,000
Replacing valves: $500-$2,000
Installing new valve seats: $300-$1,500
How Many Labor Hours Does It Take to Replace a Head Gasket?
It takes approximately 9 hours to replace a head gasket. This includes removing the old gasket, cleaning the surfaces, and installing the new gasket. The process is labor intensive and requires special tools and training.
How Much Does It Cost to Replace a Cylinder Head on a Jeep Wrangler?
If you’re looking to replace the cylinder head on your Jeep Wrangler, you can expect to pay anywhere from $1000 to $2000 for the parts and labor. This is a pretty big job, so it’s not something that you’ll want to tackle if you’re not comfortable with working on engines. If you have a mechanic do the work for you, they may charge closer to the higher end of that range.
Credit: www.cylinder-heads.com
3.6 Pentastar Head Recall
In early 2012, Chrysler announced a recall of its 3.6-liter Pentastar V6 engines. The recall was issued for a problem with the engine’s cylinder heads that could cause coolant and oil to mix, leading to engine damage.
Chrysler said that the recall affected about 42,000 vehicles equipped with the 3.6-liter engine, including the 2011-’12 Jeep Grand Cherokee, Dodge Durango, and Chrysler 300 and Town & Country minivan.
The automaker said it would notify owners of affected vehicles and repair their engines free of charge.
3.6 Pentastar Head Gasket Replacement
If your 3.6 Pentastar engine is leaking coolant, it’s likely that the head gasket is damaged. Replacing the head gasket is a fairly straightforward process, but it’s important to do it carefully to avoid damaging the engine.
Start by removing the radiator cap and draining the coolant into a clean container.
Next, remove the spark plugs and disconnect the battery. With the engine cool, you can now remove the intake manifold and cylinder heads. Be careful not to damage any of the gaskets as you remove them.
Inspect the cylinder heads and block for any damage. If there is any damage, you’ll need to have them repaired or replaced before proceeding. Once they’re inspected, you can clean all of the surfaces that will make contact with new gaskets.
Install new head gaskets making sure they’re seated properly. You may want to use sealant on both sides of the gasket to ensure a good seal.
Re-install the cylinder heads and intake manifold being careful not to over-tighten any bolts.
Refill the radiator with fresh coolant and reconnect the battery. Start the engine and check for leaks.
3.6 Pentastar Cylinder Head
The 3.6L Pentastar V6 engine features a cast-iron block and aluminum heads with hemispherical combustion chambers. The cylinders are lined with cast-in iron liners. The forged steel crankshaft is supported by five main bearings.
Forged powder metal connecting rods connect the pistons to the crankshaft. Pistons are made from an aluminum alloy and feature low-friction ring packs. The cylinder heads feature intake and exhaust ports that have been optimized for airflow and performance.
The pent-roof combustion chamber design provides a compact, yet efficient burn pattern that helps improve fuel economy and power output.The camshafts are chain driven and actuate hydraulic roller tappets.
Conclusion
This blog post discusses the cost of replacing a 3.6 Pentastar engine head. The author provides a detailed breakdown of the costs involved and offers some tips on how to save money on the replacement. Overall, the author concludes that the cost of replacing a 3.6 Pentastar engine head can be quite expensive, but there are ways to save money on the replacement.