The cost for the 2017 Ford Escape Crankcase Pressure Sensor will vary depending on where you purchase it from. However, on average, you can expect to pay between $100 and $200 for this part.
If your 2017 Ford Escape is idling rough, or if you’ve noticed a drop in fuel efficiency, it might be time to check the crankcase pressure sensor. This important sensor monitors the pressure inside the engine’s crankcase, and it can fail over time due to build-up of oil and other fluids. Replacing the sensor is relatively straightforward, but it can be pricey depending on where you take your vehicle.
We’ve compiled some average costs below to give you an idea of what you can expect to pay.
At an independent garage, the cost for a new 2017 Ford Escape crankcase pressure sensor will be around $200-$250 on average. If you’re taking your vehicle to a dealership, the cost will be closer to $300-$350.
And finally, if you’re comfortable doing the work yourself, a new sensor will set you back about $100-$150. No matter which option you choose, replacing this sensor will help keep your Ford running smoothly for years to come!
Ford Escape CRANKCASE PRESSURE SENSOR P051B 2.0L EcoBoost 2017
2017 Ford Escape Crankcase Pressure Sensor Location
If you’re looking for the 2017 Ford Escape crankcase pressure sensor location, you’ve come to the right place. This quick and easy guide will help you find the sensor in no time.
The crankcase pressure sensor is located on the top of the engine, near the front.
It’s a small, round sensor with a single wire coming out of it. To access it, simply remove the engine cover. Once you have the cover off, locate the sensor and disconnect the wire.
You can then remove the sensor from its mount and replace it with a new one.
2017 Ford Escape Crankcase Pressure Sensor Replacement
If you have a 2017 Ford Escape with the 2.0L Ecoboost engine, you may have noticed an issue with your crankcase pressure sensor. This can cause your engine to run rough and produce a knocking sound. If you’re experiencing these symptoms, it’s likely that your crankcase pressure sensor needs to be replaced.
Here’s a quick guide on how to do just that:
1. Locate the crankcase pressure sensor on the side of the engine block. It will be near the oil filter housing.
2. Using a ratchet and socket, remove the two bolts that hold the sensor in place.
3. Pull the old sensor out and discard it.
4. Install the new sensor by threading it into place and tightening down the bolts snugly.
Crankcase Pressure Sensor 2017 Ford Fusion Cost
The average cost of a crankcase pressure sensor for a 2017 Ford Fusion is around $120. This price can differ depending on the make and model of your vehicle as well as the year. The location of the sensor can also affect the price.
If the sensor is located in an easily accessible area, then it may cost less to replace than one that is difficult to reach. Depending on the severity of the problem, you may only need to replace the sensor, but in some cases, you may need to replace other parts as well such as the gasket or oil filter.
2017 Ford Focus Crankcase Pressure Sensor
If your 2017 Ford Focus has an issue with the crankcase pressure sensor, you may notice a loss of power or fuel economy. This can be a serious problem, so it’s important to know what to do if it happens to your car.
The crankcase pressure sensor is located near the engine and monitors the pressure in the engine’s oil system.
If the sensor detects a drop in pressure, it will send a signal to the computer which will then adjust the fuel mixture accordingly. A drop in pressure can be caused by a number of things, such as a leak in the oil system, worn piston rings, or even just dirty oil.
If you think that your car may have an issue with the crankcase pressure sensor, the first thing you should do is check the oil level and quality.
If everything looks good there, then take your car to a mechanic for further diagnosis.
Crankcase Pressure Sensor Ford Part Number
If your car is low on oil, it will trigger a warning light on your dash. This is to alert you so that you can add more oil to the engine. But what if the light comes on and you know your oil level is fine?
It could be a faulty Crankcase Pressure Sensor.
The Crankcase Pressure Sensor monitors the pressure in the engine’s crankcase. If the sensor detects too much pressure, it will trigger the warning light.
If you’re getting the warning light and you know your oil level is fine, check your Crankcase Pressure Sensor. Ford part number for this sensor is XXXXXXXX. You can find this part at most auto parts stores or online retailers.
Ford Crankcase Pressure Sensor
The Ford Crankcase Pressure Sensor is located on the engine block, near the oil filter housing. It monitors the pressure inside the crankcase and sends a signal to the powertrain control module (PCM). If the sensor detects an abnormal pressure condition, it will trigger a diagnostic trouble code (DTC).
The most common symptom of a faulty crankcase pressure sensor is an illuminated check engine light. Other symptoms may include rough idling, stalling, and poor fuel economy. If you suspect that your crankcase pressure sensor is failing, have the vehicle inspected by a professional technician.
2017 Ford Fusion Crankcase Pressure Sensor
If your 2017 Ford Fusion is idling roughly or stalls occasionally, it may be time to check the crankcase pressure sensor. This sensor monitors the amount of pressure in the engine’s crankcase and sends a signal to the computer which then adjusts the air-fuel mixture accordingly. A faulty sensor can cause all sorts of drivability issues so it’s important to replace it if it’s not working properly.
Here’s a step-by-step guide on how to do just that.
1) Jack up the front of your Fusion and support it with jack stands. Then, crawl under the car and locate the oil filter housing on the driver’s side of the engine.
2) Unscrew the oil filter housing cap (it should be easy to turn by hand) and let any excess oil drain out into a catch pan.
3) Disconnect the electrical connector from the old sensor (it will likely be held in place by a retaining clip). You may need to use a small flathead screwdriver to release the clip.
4) Use an O-ring pick or similar tool to remove the old O-ring from around base of sensor (be careful not to damage O-ring groove). Discard old O-ring. 5) Remove old sensor from housing by twisting counterclockwise until it comes loose (do not use excessive force).
Inspect housing for any damage and clean away any debris before installing new sensor. 6) Coat new O-ring with fresh motor oil and install in groove around base of new sensor. 7) Screw new sensor into place clockwise until snug (do not overtighten – stop when you feel resistance).
8) Reconnect electrical connector to new sensor.
Crankcase Pressure Sensor 2015 Ford Expedition
As the name suggests, the Crankcase Pressure Sensor is a sensor that monitors the pressure in the crankcase of your 2015 Ford Expedition. This is important because it can help prevent engine damage by alerting you to any abnormal pressures that may be present. There are two main types of Crankcase Pressure Sensors – those that measure absolute pressure and those that measure relative pressure.
The type of sensor used in your Expedition will depend on what type of engine it has.
The most common cause of a faulty Crankcase Pressure Sensor is a build-up of oil or other fluids in the area where the sensor is located. This can happen if there is an oil leak or if the crankcase ventilation system is not working properly.
If you notice any leaks or strange smells coming from your engine, it’s best to take it to a mechanic to have them check for any potential issues.
If your Crankcase Pressure Sensor does need to be replaced, don’t worry – it’s a relatively straightforward process that most mechanics should be able to do quickly and easily.
Credit: www.youtube.com
Where is the Crankcase Pressure Sensor Located on a 2017 Ford Escape?
The crankcase pressure sensor on a 2017 Ford Escape is located near the oil filter, on the side of the engine. It is used to measure the pressure in the crankcase, and send a signal to the engine control unit (ECU) to adjust the engine’s timing and fuel mixture accordingly.
What is a Crankcase Pressure Sensor?
A crankcase pressure sensor is a device that measures the pressure inside the engine’s crankcase. The sensor produces a signal that can be used to monitor the engine’s oil pressure, as well as the pressure of other fluids in the crankcase. Crankcase pressure sensors are typically mounted on the side of the engine block, and they may be integrated with an oil pressure sensor or a fuel pressure sensor.
What is Code Po51B on 2017 Ford Escape?
Assuming you are referring to a diagnostic trouble code:
Code P0351 indicates that there is a problem with the ignition coil “A” on cylinder 1. This code is often accompanied by others codes, such as P0301, P0302, P0303, and/or P0304 (which would indicate a misfire on cylinders 1, 2, 3, and/or 4 respectively).
The most common cause of this code is a spark plug or ignition wire that has failed. However, it could also be caused by an issue with the ignition coil itself, the engine control module (ECM), or a fuel injector.
If you have this code, the first thing you should do is check all of your spark plugs and wires.
If they look good, then move on to testing the ignition coil. If the coil tests good but the code persists, then you may have an issue with your ECM.
How Do You Replace a Crankcase Pressure Sensor?
If your car is displaying any of the following symptoms, it may be time to replace your crankcase pressure sensor:
-The check engine light is on
-You notice a decrease in fuel economy
-Your car is stalling or having trouble starting
-There is an oil leak coming from the front or back of the engine
-The oil level in your car drops quickly
Here are the steps you’ll need to take to replace your crankcase pressure sensor:
1. Locate the sensor. The location will vary depending on your make and model of car, but it is typically located near the oil filter or close to where the dipstick enters the engine.
Consult your owners manual if you can’t find it.
2. Unplug the electrical connector from the sensor. You may need a small flathead screwdriver to help with this step.
Some models have a locking tab that needs to be disengaged before you can unplug it.
3. Remove any bolts holding the sensor in place using an appropriately sized socket or wrench. Again, consult your owners manual for specifics on how many bolts there are and what size they are.
4. Pull out the old sensor and compare it to the new one to make sure they are identical before proceeding further. If they aren’t, consult with a mechanic before proceeding as using an incorrect replacement could cause damage to your engine.
5 Put some fresh motor oil on the O-ring ofthe new sensor (this will help create a seal) and then thread it into place by hand until it’s snug against whatever surface it’s mounting too.
. Don’t overtighten it! Use a torque wrench set at low tensionto finish tightening according to specifications given in your owner’s manual – usually between 10 and 20 ft lbs.
Conclusion
The average cost for a Ford Escape crankcase pressure sensor replacement is between $113 and $142. Labor costs are estimated between $44 and $56 while parts are priced at $69. This range does not include taxes and fees, and does not factor in your specific vehicle’s location.